How to Back-Flush an Aquarium Chiller

COIL CLEANING · TITANIUM HEAT EXCHANGER

  • ~1 hrstart to finish
  • 2x a yearfor most tanks
  • 30-60 mincleaner circulating
  • 0special tools

Back-flushing means running water through the chiller the wrong way. It washes out the slime, sand and scale that build up inside the coil, so heat moves from your water into the refrigerant again the way it did when the chiller was new. Here is how to do it at home with a bucket and a small pump.

Why Signs What you need Steps Do not Questions

Why back-flush?

Normal flow always pushes debris the same way, so it packs against the same spots inside the coil. Reverse flow pulls it back out of the bends it is stuck in. Add a mild acid and the thin mineral crust on the tube walls dissolves too. That crust is an insulator: even a thin layer makes the compressor run longer for the same drop in temperature.

Signs the coil needs it

  • Longer run times. The chiller runs noticeably longer than last season to hold the same temperature, with the same lights and room.
  • Weaker flow out. Less water comes out of the return than before, and the pump and pre-filter are clean.
  • Slime at the fittings. Brown or white film inside the hose ends when you pull them off.
  • Hard water. White crust on heaters, pumps or the tank rim means the same is forming in the coil.

What you need

  • A clean bucket, 3 to 5 gallons, used for nothing but tank work.
  • A small submersible pump, roughly 100 to 400 GPH. A spare powerhead with a hose barb works here, because nothing is being lifted far.
  • Two lengths of hose that fit the chiller's hose barbs, and clamps.
  • White vinegar from the grocery store, or citric acid powder.
  • Fresh water for rinsing, and a towel.

Step by step

Back-flush loop: bucket, small pump, chiller run backwardA small pump in a bucket pushes cleaning solution into the chiller's outlet fitting. The solution comes out of the inlet fitting and drains back into the bucket, so the coil is washed in the opposite direction to normal flow.Bucketvinegar + waterPUMP72.0ChillerOUT fittingIN fittingpushed in backwardback to the bucket, loosened slime and scale with itunplugged
  1. Unplug and isolate. Unplug the chiller first, then the pump that feeds it. Close the valves on each side or clamp the hoses, and take the chiller off the loop. Tip it over a towel so the water inside drains out. The chiller stays unplugged for the whole job: the compressor must not run with no water moving.
  2. Rig the loop backward. Set a small submersible pump in a clean bucket. Run a hose from the pump to the chiller's OUT fitting, and a second hose from the IN fitting back into the bucket. Pushing water in the wrong way lifts out debris that has wedged against the inlet side of the coil.
  3. Fresh-water flush. Fill the bucket with plain fresh water and run the pump for five minutes. Dump the cloudy water. On a reef, this first rinse often comes out brown with slime.
  4. Circulate the cleaner. Refill the bucket with white vinegar and fresh water mixed about half and half, or fresh water with citric acid powder (about a tablespoon per gallon). Let it circulate for 30 to 60 minutes. Hard white scale takes the longer time. If the solution turns cloudy fast, dump it and mix a fresh batch.
  5. Rinse it out completely. Empty the bucket, rinse it, and run plain fresh water through the chiller for at least ten minutes. Do it twice with fresh water each time. Nothing from the cleaning batch should reach your tank.
  6. Back on the tank. Reconnect the chiller in the normal direction: pump to IN, OUT back to the tank. Open the valves, start the pump, check every fitting for drips, and only then plug the chiller back in. Watch the first cooling cycle.

Do not

  • Do not run the chiller during the flush. Keep it unplugged until the normal loop is back and water is moving.
  • Do not use bleach, muriatic acid or drain cleaner. Vinegar or citric acid is enough for aquarium scale.
  • Do not skip the rinse. Two full fresh-water rinses before the chiller sees tank water again.
  • Do not force a hose barb. Warm the hose end in hot water so it slides on; cracked fittings leak later.

Your chiller's manual comes first: if it gives a different cleaning method, follow the manual. For the rest of the routine, see the chiller care guide. Setting a chiller up for the first time? See chiller installation. More answers on the chiller questions page, or text us a photo.

Questions

How often should I back-flush an aquarium chiller?

Once or twice a year suits most home tanks. Do it more often in hard water, in ponds, or when the chiller has started to run longer to hold the same temperature.

Is vinegar safe for a titanium coil?

Yes. Titanium does not react with the mild acid in household vinegar or citric acid, and the solution is rinsed out before the chiller goes back on. Skip bleach, muriatic acid and drain cleaners: they are hard on rubber seals and plastic and leave residue you do not want near fish or coral.

Can I back-flush without taking the chiller off the stand?

If you have unions or valves on both sides you can close them, disconnect, and hook the bucket hoses up right where the chiller sits. Put a towel and a tray under it.

The chiller still runs long after a flush. What next?

Most cooling complaints are airflow or water flow. Clean the fins and grille, make sure the pump still moves enough water at your head, and check where the probe sits. Then text us a photo of the setup.